Your cart
There are no more items in your cart- Directories and catalogs
- 1 likes
- 4611 views
Bearing Fitting Position | Bearing designation | bearing Type | Number |
reverse shaft | 210 | Ball radial single-row | 1 |
reverse shaft | 215 | Ball groove single-row | 1 |
Val propeller intermediate | 7310 | roller cone Single row | 2 |
Val PTO Front | 804,707 K4 | Needle groove Single row without inner ring and a separator | 16 |
PTO shaft (shaft driven) | 210 | Ball groove single-row | 1 |
PTO shaft (shaft driven) | 211 | Ball groove single-row | 2 |
PTO shaft (shaft driven) | 311 | Ball groove single-row | 1 |
PTO shaft (shaft leading) | 308 | Ball Radial single-row | 1 |
PTO shaft (shaft leading) | 409 | Ball groove single-row | 1 |
power take-off shaft (PTO) | 804,704 K5 | Needle groove Single row without inner ring and cage | 8 |
PTO shaft (drive shaft) | 111 | Ball groove single-row | 1 |
PTO shaft (drive shaft) | 305 | Ball groove single-row | 1 |
Val PTO (drive shaft) | 308 | Ball groove single-row | 2 |
pump drive shaft hinge | 305 | Ball radial single-row | 2 |
Fork double assembly | 804,707 K4 | Single row without a needle groove of the inner ring and cage | 8 |
Engine (block pro interstitial gear starter motor) | 180502 K1S9 | Ball groove Single row with double-sided seal | 2 |
Engine (shaft crank compressor) | 207 | Ball groove single-row | 1 |
Engine (shaft crank compressor ) | 50207 | Ball groove single-row groove on the outer ring | 1 |
Engine (shaft cranked starting motor) | 205 K | Ball groove single-row | 1 |
engine (shaft crankshaft starter motor ) | 2206 K | Roller radial short cylindrical rollers without flanges on the outer ring | 1 |
The motor (shaft crankshaft starter motor) | 102206 M | roller radial short cylindrical roller flangeless outer ring and two locking washers | 1 |
Engine (drive booster pump shaft) | 29 | Ball groove single-row | 1 |
Engine (shaft prime mover controller) | 202 | Ball groove single-row | 2 |
Engine (shaft of the fuel pump regulator) | 201 | Ball groove single-row | 1 |
motor (starter motor gear shaft) | 305 K | Ball groove single-row | 1 |
motor (starter motor gear shaft) | 308 | Ball groove single-row | 1 |
Engine (upper cap fuel pump regulator) | 29 | Ball groove single-row | 1 |
motor (generator) | 180504 | Ball groove Single row with double-sided seal | 2 |
Engine (cargo fuel pump regulator) | 1000095 | Ball groove single-row | 2 |
Engine (cargo control fuel pump) | 941/6 | needle roller with an outer ring with a through hole without a separator | 4 |
Engine (cam shaft of the fuel pump) | 204 | Ball groove single-row | 2 |
Engine (magneto) | 6012 | Ball Angular Single row removable outer ring | 2 |
Engine (flywheel) | 60209 | Ball groove single row with one side plate | 1 |
Engine (mechanism manual start motor starting) | 60201 | Ball groove single row with one side plate | 2 |
engine (push abutment starter motor clutch) | 8109 | Thrust ball single | 1 |
engine ( pump water) | 305 K | Ball groove single-row | 2 |
Engine (extractor clutch) | 46120 | Ball Angular single-row one-piece with the bevel on the outer ring with contact angle α = 26º | 1 |
motor (drive assembly) | 305 K | Ball groove single-row | 2 |
engine (intermediate gear starter motor) | 202 | Ball groove single-row | 2 |
Engine (tension roller) | 180205 K4S9 | Ball groove Single row with double-sided seal | 2 |
Engine (bifurcated fuel pump governor lever) | 1000095 | Single row radial ball | 2 |
Engine (fuel pump bifurcate lever knob) | 942/8 | Roller needle with an outer ring with a through hole without a separator | 2 |
engine (hub starter motor reducer) | 8106 | Thrust ball single | 1 |
motor (pinion drive magnetos) | 202 | Ball groove single-row | 2 |
Engine (gear intermediate fuel pump) | 25 | Ball groove single-row | 2 |
differential (housing) | 7517 | Roller conical Single row | 4 |
Transmission (shaft secondary) | 311 | Ball groove single-row | 1 |
Transmission (shaft secondary) | 313 | Ball groove single-row | 1 |
Transmission (shaft primary) | 311 | Ball groove single-row | 1 |
Transmission (shaft primary) | 313 | Ball groove single-row | 1 |
Transmission (pump driver) | 206 | Ball groove single-row | 2 |
rear axle (drive shaft) | 313 | Ball groove single-row | 1 |
rear axle (drive shaft) | 12 311 K1M | Roller radial short cylindrical rollers with single-breasted outer ring | 1 |
Bridge front (drive shaft) | 311 | Ball groove single-row | 1 |
Bridge front (drive shaft) | 313 | Ball groove single-row | 1 |
Coupling back | 1000915 | ball groove single-row | 4 |
Coupling front | 1000915 | ball groove single-row | 4 |
Prop intermediate | 208 | Ball groove single-row | 2 |
Transfer box (shaft primary) | 313 | Ball groove single-row | 1 |
Transfer box (shaft primary) | 2411 | roller radial short cylindrical rollers without flanges on the outer ring | 1 |
Steering (pump drive shaft) | 305 | Ball sake cial Single row | 2 |
steering (the steering shaft) | 2306 | Roller groove with short cylindrical rollers without flanges on the outer ring | 3 |
steering (steering shaft mechanism) | 8206 | Thrust ball single | 2 |
steering (the steering shaft) | 1206 | ball groove double row spherical with a cylindrical bore of the inner ring | 1 |
steering (steering section) | 943/45 | Roller needle with an outer ring with a through hole without a separator | 2 |
hub wheel gear | 7224 | tapered roller single-row | 4 |
Clutch (body off mechanism) | 46120 | Ball Single row angular ball-one bevel on the outer ring with a contact angle α = 26º | 1 |
Creeper (shaft) | 408 | Ball groove single-row | 1 |
creeper (shaft) | 50408 | < td> Ball groove single-row groove on the outer ring1 | |
Hinge double | 804,704 K5 | Needle groove Single row without inner ring and cage | 8 |
pinion leading | 7313 | tapered roller single-row | 2 |
Gear leading | 7614 | tapered roller single-row | 2 |
the transport of several pinion | 113 | Ball radial single-row | 2 |
The gear epicyclic | 2,007,122 | tapered roller single-row | 4 |